How to install the voice control lamp for the voice control lamp is always bright
As the name suggests, the voice-activated lamp is a kind of voice-activated electronic lighting device, which has the advantages of simple operation, flexibility and strong anti-interference ability. But also some of the problems encountered in use, for example, said voice-activated lights have been lit, the voice-activated lights always on how back thing? In the following content, Xiaobian will bring about the solution to this problem, and how to install the voice control lamp to help you better use the voice control lamp.
First, how to install the voice control lamp
1, light bulb installation
The first thing to install the voice-activated lamp is to turn off the main power valve in the home, and then directly connect the two wires under the voice-activated lamp holder to the reserved line, and then fix the lamp holder with screws;
2, switch installation
When installing the voice-activated light switch, it should be noted that there are 4 wires for the general voice-activated light switch device, two of which are connected to the neutral wire, one is connected to the fire-only access line, and the other is connected to the fire wire;
(1) First open the position where the switch is reserved. At this time, you can see the four terminals of red, yellow, blue and green.
(2) After disassembling the switch box cover, open the back of the box. Under normal circumstances, L1 is connected to the red line, 2F is connected to the yellow line connector, and 3A is connected to the green line.
(3) Finally fix the voice control light switch, then punch the hole with the power drill, install the rubber plug in it, then fix the wire box with the screw, and then install the side cover.
Note: When the voice control lamp is installed, be sure to test it. If it is during the day, you can block the photosensitive device of the voice control lamp before testing.
Second, the voice control light is always bright, what happened?
1. The voice control probe is broken.
When the voice control probe of the voice control lamp is broken, the voice control lamp will continue to be bright, and only need to buy the same type of voice sensor to replace it;
2, there is a problem with the thyristor
The sound control lamp is always on because the thyristor in the control unit has a problem, because the general control light will automatically turn off after 60 seconds of receiving the signal. If the thyristor has a problem, the voice control light will not automatically go out. And thus will continue to be bright;
3, the bulb power is too small
Because there is no sound, the relay will send a small current to make the lamp holder work. After the sound is converted into an electric signal, the relay will send the current to the lamp. If the lamp power is too small, the small current can also be lit. light bulb;
4, the environment is noisy
If the voice-activated light is always in a more noisy environment, then the surrounding sound will continue, and the voice-activated light will continue to receive the signal, then the voice-activated light will always be in working condition and will continue to light.
3. Can the sound-activated lamp head use energy-saving lamps?
The voice-activated lamp head can not use the energy-saving lamp under normal circumstances, because the energy-saving lamp and the voice-activated lamp work differently. If the energy-saving lamp is used on the voice-activated lamp head, the energy-saving lamp or the voice-activated lamp may be seriously affected. The service life.
Because the last switch of the voice-activated lamp head is a two-way thyristor, there will be a small control angle when it is turned on, which will cause the device conduction angle to be less than 180 degrees. This situation has a certain influence on the energy-saving lamp. If the energy-saving lamp flickers very much, it means that the conduction angle may be close to 90 degrees, and the voltage is low. At the same time, it also shows that the energy-saving lamp itself has poor adaptability to the voltage range. If it is a good energy-saving lamp, it needs to be connected with a diode to work normally.
Note on purchase: Generally, when purchasing the sound and light control switch, you need to pay attention to the type of light source used. If you use energy-saving lamps, you should choose the sound and light control switch for energy-saving lamps.
(Recommended reading: Sound control lamp installation precautions )
The above is about how to install the voice-activated lamp, the sound-activated light has been bright, what is going on , I hope to help everyone! Qi installed network, China's well-known large-scale decoration platform, decoration leading brand. If you want to make a new design, you are advised to apply for the free design service of the net, and help you plan a reasonable space layout and exquisite design through the professional designer's on-site measurement room.
>> Click here for professional designer free room design
Disclaimer: We have used all means to find the source of the picture or content. We have not found the relevant right holder. Please ignore the negligence. If the relevant rights holders see it, please contact us in time. We will delete and proceed as soon as possible. Handle it properly.
Milk Storage Bag,Breast Milk Cooler Bag,Breast Milk Storage Containers,Breastmilk Bags
Zhejiang Carebao Co., Ltd , https://www.carebao.com