The advantage of dry floor heating is how to install dry floor heating correctly
Floor heating is a device commonly used for heating in homes, especially in the north. Floor heating is very frequently used, and floor heating is usually divided into dry floor heating and wet floor heating. So what are the advantages of dry floor heating , how to install dry floor heating ? Let's take a look at the following content!
Where is the advantage of dry floor heating
1. Rapid heating: This reason is easy to understand, because dry floor heating does not have a cement backfill layer, so it can transfer heat faster, and floor heating can allow users to enjoy warmth in only 30 minutes, and the effect is very high.
2. The floor height is small: the floor height of the dry floor heating is relatively small, about 50 mm thinner than the wet floor heating, so it is installed in the home, which can effectively increase the area of ​​the room and is suitable for home installations of different floors.
3. Simple construction: The construction method of dry floor heating is very simple, saving the cement backfilling steps of traditional floor heating, the overall installation is very simple, and it saves a lot of time.
4. Good system stability: Another advantage of dry floor heating is that the system has good stability. It uses a modular design, the entire coil is installed, and it is reliable and reliable.
How to install dry floor heating correctly
1. Planning the layout direction
The installation of dry floor heating requires certain steps. First of all, according to the floor heating pipe layout, the distribution of the inlet and return pipes of the overall floor heating area should be determined, and the floor heating area in each area should be basically balanced to clean up the ground waste.
2. Laying the floor heating module
The corrugated module is directly communicated and fixed in the early stage. It is embedded in the module in the direction of the corrugation and tiled. The aluminum plate is connected to the top of the corrugation along the leveling tower. , Draw a wire saw notch on the floor corrugated by the pipeline; the floor-free corrugated module is laid directly on the flat cement surface, the elbow plates are embedded on both sides of the pipe elbow, and the pipe groove of the elbow plate is connected with the module pipe groove
3. Trim the module seams and side seams
Use aluminum foil tape to paste the joints between all the modules flat. If the wall is lined with a pipe, it needs to be filled with semi-dry mud sand to be flat with the module powder.
4. Pay-off pipe
First fix the water inlet of the water separator, and then put the wire into the floor heating pipe according to the direction of the pipe groove. The surface does not need any fixing and covering. The pipe elbows on both sides are directly fixed on the lining board with the reflective film by the floor heating pipe clamp. Keep a proper bending radius at the head, and do not bend the floor heating pipe.
5. Water injection test pressure installation floor
After installing and fixing the loop pipes of each area of ​​the floor heating, inject water to wash the coils of the heating area in sequence, and carefully check whether the area coils of the floor heating pipe are kept smooth.
Everyone must understand the advantages of dry floor heating . Although it has many advantages, it also has some shortcomings. After all, it is inevitable that there are shortcomings in technology in the domestic market, and there are not many families. , So you have to be more careful when installing.
What, the decoration still uses his own money? ! The Qi family is decorated in installments, with an ultra-low annual interest rate of 3.55% and a maximum loan of 1 million. Apply now to enjoy the discount
If you are interested in brand cooperation, content cooperation, and advertising of this website, please send an email to :.
The Training head made of high-temperature synthetic fiber Hair. All of the hair has been chemically washed and disinfected. If you want to flat/curl iron your hair, we recommend that the temperature can not exceed 150 degrees, and not exceed 15 seconds every time.
The Hair length is 26-28 inches (from the forehead to the back hair end), individual hair strand.
It is suitable for cosmetology students or anyone to practice straightening, cutting, curling, braiding, setting and marcel. But can not dye, bleach and make up.
An ideal choice for hairdressing students to practice, little girls to play game or as a teaching supplies for kindergarten or primary school.
The hair is implanted firmly on the braiding Mannequin Head to ensure there is nearly no losing hair. For first used, please comb the hair first; It is common for losing a little hair first time and won't happen the next time.
Our mannequin head with hair comes with with an adjustable clamp holder which allows an easy way for hair styling or to display wigs and hats which can be swiveled and clamped on desk.
Synthetic Training Head,Synthetic Hair Training Head,Cosmetology Practice Head,Hairdressing Mannequin Head
Xuchang Le Yi De Import And Export Trade Co., Ltd. , https://www.lileaderbeauty.com